Battery Report Summary – Surface Laptop 7 (Snapdragon X Elite)
Report Date: November 27, 2025 Device: Microsoft Surface Laptop 7, Snapdragon X Elite Charge Cycles: 9 1. Key Data Battery Name: SurfaceBattery Manufacturer: SWD Design Capacity: 52,330 mWh Full Charge Capacity: 53,850 mWh Cycle Count: 9 2. Usage Observations Despite the battery being new (only 9 cycles), the report shows abnormally fast discharge. Examples from the report: On November 25, the battery dropped from 30% (16,340 mWh) to 23% (12,520 mWh) in ~20 minutes of use. On November 27, during “connected standby,” the battery fell from 77% (41,200 mWh) to 55% (29,440 mWh) within about one hour. These behaviors are inconsistent with expectations for a new device with full capacity. . Technical Analysis Battery authenticity: The data indicates the battery is original (manufacturer SWD, capacity matches design). Primary issue: The discharge rate is unusually fast and unstable, which is not normal for a battery with so few cycles. Possible causes: Defect in the Battery Management System (BMS). Internal cell imbalance. Firmware/driver issue affecting power management. 4. Conclusion and Request The Surface Laptop 7 is showing abnormal battery behavior despite being new and original. Any idea where this problem comes from? Any solution? Thanks in advance!
Surface Laptop 7, will not boot after system restore
Brand new Surface 7 13.8", just received the package yesterday. I've set it up for my wife, but shortly after network just started timing out querying the router's DNS server (Router is fine, multiple other phones, windows 10 & 11, linux, mac machines work without a hitch). Tried some fixes to no avail, and decided on a system restore just in case I've messed something up during setup. System restore looked like it worked, but laptop restarted and ended up with a bluescreen (something kernel something). System restore is there just fir that, right? Well, I've started it nine hours ago. Now it's just boot looping with the "preparing" bit and then shuts back down. It's been like that the whole day. I've even tried to get a USB stick to have the requisite livecd/recovery media, but it doesn't the new Surface ARM-based processor. What can we even do at this point?
Various multiple monitor issues on Surface Laptop Studio (1) since driver updates.
Issues started directly after NVIDIA - Display - 32.0.15.7344 or Surface - Extension - 14.54.139.0 both installed on 2025-10-21 Issues occur when a second monitor is attached, and either extend or duplicate screens is selected. Using only one screen has no issue. Checked with different cables, bypassing HUB and different monitors. All show the same issues. Issues are (but not limited to) 3D (Vulkan) applications in non full-screen mode glitch with a triangle like tearing between the frames. This is a screenshot from a derivate of the Vulkan tutorial. To illustrate the tearing I alternate the clear colour to black and green. With only one monitor selected (either one) the green flashes as expected. With two monitors, even with duplicate display(!), this tearing which seems to be the presentation not waiting for the chain to finish rendering. Again this was all fine before the update. In borderless full window mode it is okay, as the NVIDIA driver doesn't use the INTEL integrated swap chain. Clear type tech is not working, and text is chroma distorted. Happens in all apps, including Microsoft ones. I can literally have an app like visual studio running on the second monitor and the text has serve chroma distortion, and then I change monitor setting to just that monitor and the text is correct. and back and forth. General glitches on apps when resizing, frames of windows appear for a second.
Trouble Activating Ultimate Performance Plan on My Surface Laptop
Hi everyone, I’m trying to enable the Ultimate Performance power plan on my Surface device. I’ve already used the command powercfg -duplicatescheme e9a42b02-d5df-448d-aa00-03f14749eb61, and it shows up in my system. However, when I try to activate it using powercfg /setactive [GUID], I get an “Invalid Parameters” error—even though the GUID matches exactly what was listed under powercfg /list. My current active plan is “High performance” (custom-made). Has anyone else encountered this issue on a Surface laptop? Is this plan blocked or incompatible with certain Surface models, or am I missing a step? Would appreciate any insights or tips! Thank you so much for your attention and participation.Display problems with Surface 1872
Hi, I hope someone can help me here. I was given a Surface 1872 with a broken screen to fix. The picture was viewable but yes, the screen needed replacing. I cleaned out the broken screen and bought a brand new one (that was a mistake that I won't make again !!), I then attached the new screen in place of the broken one (not in the lid, just laying above it) and attached it using the 4 cables. The laptop booted up, but there was nothing showing on the screen. I attached a USBC cable and plugged it onto my Monitor's HDMI port and that screen was fine. I then, by accident, touched the laptop screen and bizarrely, the touchscreen was working, just only visible on my monitor, not the new laptop screen. Googling this told me that it was probably a faulty screen. I then bought a second hand replacement screen, apparently tested and fully working, but as part of the whole top, i.e. in and attached to the lid. I replaced the laptop screen again and this time there was still nothing on it, but my monitor showed some flickering & some lines. I therefore disconnected the screen re-attached all of the cable again and rebooted. I hear the laptop boot up, but now I am getting nothing on either screen !!! What on earth could have caused this ? Why, at least, do I not have video on my Monitor when I did before ?!? I have tried CTRL-Win Key-Shift-B & numerous other suggestions but nothing has so far made a difference 😢 ... Any help or advice would be a Godsend !!!
Surface Laptop 5 abysmally horrible battery life
I bought this laptop 2 years ago for $1.4k. I expect it to have a battery life that lasts more than 3.75 hours. The charger it came with is also incredibly finnicky and this webcam makes everything look like it was recorded on a D-list smart fridge. The only think this crapshoot is good for is the aesthetic. Functionally it's useless. I really expected better from a reputed company like Microsoft.
Surface Laptop 4 heats up with minimal use or idle, even more when charging
A couple of months ago, I started noticing the fans on my laptop spinning up during pretty light use. Normally they never turned on, except for during heavy use. Now the fans are on by default and the bottom of the chassis is constantly warm, and when charging it's almost too hot to touch. I don't recall having installed something around the same time this started happening. I've never opened the laptop or cleaned the fans. When I open the task manager it's nothing crazy (this is while the fans are very audibly on and the bottom of the laptop is very hot) Any suggestions are more than welcome, thanks! PS Device specifications Processor AMD Ryzen 5 Microsoft Surface (R) Edition 2.20 GHz Installed RAM 8.00 GB (7.45 GB usable) System type 64-bit operating system, x64-based processor Windows specifications Edition Windows 11 Home Version 22H2 Installed on 23/09/2022 OS build 22621.3007 Experience Windows Feature Experience Pack 1000.22681.1000.0
Surface Laptop 5 not recognizing USB A or USB C ports - have tried everything
Brand new Surface Laptop 5 - Brand new Windows 10 - upgraded to Windows 11 - ran all software, OS and firmware updates, multiple times. Also disabled/re-enabled all USB options in Device Manager, but nothing works. I need to set this laptop up for work, but I don't know what to do next. Please help. I keep getting this message. I have verified that this USB works on other PCs/laptops.
Surface 3 laptop hardware issue
I have just returned a brand new Surface 3 laptop bought 2 days ago. It kept turning itself off constantly. Tech support at the HQ of the store I purchased it from spent considerable time trying to diagnose the problem over the phone. In the end it was diagnosed as a hardware problem not a software. This is very disappointing for a laptop of this quality which surely cannot have passed stringent quality control tests (assume China). I hope my replacement next week is going to be OK.Surface Laptop 3 - applications starts up slow and with delay
Problem Description: Every application starts up with a delay of 1-2 seconds. Opening another screen of an running program does initalize instantly though.. Build and Firmware I'm running the 20H2 build 19042.685 and have the Surface Laptop 3 firmware from november 2020 installed (SurfaceLaptop3_Win10_18362_20.101.8577.0) Examples: - Applies to any application, offline tooling such as Draw.io, command prompt - Opening a new tab in Chrome is instantly, but when I go to an URL it tends to take seconds before the page is initialized to actually perform and connect to the designated URL. - Opening Git bash takes 2 seconds and then it takes up to a minute to load its content before I can perform any commands Does anyone have any experience regarding my current state?
